features regulated converters ? wide 4:1 input voltage range ? 1.6kvdc isolation ? ul certifed ? effciency up to 88% ? fixed operating frequency ? six-sided continuous shield pd-1 rev.: 1/2016 www.recom-power.com dc/dc converter 3 y e a r w a r r a n t y 3 description the rp15-aw series are ultraminiature wide input voltage range power dc/dc converters in a case half the size of industry standard 15w converters. despite their small size, the rp15-aw converters are fully specifed devices with output currents up to 4 amps, no minimum load, 1600vdc isolation and low ripple/noise fgures. the outputs are also fully protected against short circuits, overcurrent and overvoltage. the rp15-aw series will fnd many uses in applications where board space and/or board height is at a premium. e196683 15 watt single & dual output rp15-aw selection guide part number input output output input (1) effciency (1) max. capacitive voltage range voltage current current typ. load (2) [vdc] [vdc] [ma] [ma] [%] [f] rp15-243.3saw (3,4) 9-36 3.3 4000 640 86 12000 rp15-2405saw (3,4) 9-36 5 3000 727 86 6000 rp15-2412saw (3,4) 9-36 12 1300 747 87 1000 rp15-2415saw (3,4) 9-36 15 1000 718 87 660 rp15-483.3saw (3,4) 18-75 3.3 4000 320 86 12000 rp15-4805saw (3,4) 18-75 5 3000 359 87 6000 rp15-4812saw (3,4) 18-75 12 1300 374 87 1000 rp15-4815saw (3,4) 18-75 15 1000 359 87 660 RP15-2405DAW (3,4) 9-36 5 1500 735 85 3000 rp15-2412daw (3,4) 9-36 12 625 718 87 520 rp15-2415daw (3,4) 9-36 15 500 710 88 330 rp15-4805daw (3,4) 18-75 5 1500 368 85 3000 rp15-4812daw (3,4) 18-75 12 625 363 86 520 rp15-4815daw (3,4) 18-75 15 500 359 87 330 ul60950-1 certifed ordering examples rp15-2405saw/p = 24v 4:1 input, 5v output, positive logic ctrl pin and trim pin ftted. rp15-4805daw-hc = 48v 4:1 input, 5v output, premounted heat-sink (no trim pin with dual output) model numbering input voltage output voltage s ingle or d ual rp15-__ __ _aw/_ _ notes: note3: standard part is without suffxes and trim and ctrl pins are not ftted. add suffx p for ctrl function with positive logic (1=on, 0=off) and trim pin for single output add suffx n for ctrl function with negative logic (0=on, 1=off) and trim pin for single output note4: add suffx -hc for premounted heat-sink and clips package (4) control logic (3) notes: note1: values at nominal input voltage and full load. note2: test by minimum vin and constant resistor load.
pd-2 rev.: 1/2016 www.recom-power.com dc/dc converter rp15-aw series basic characteristics parameter condition min. typ. max. input voltage range nom. vin = 24v nom. vin = 48v 9vdc 18vdc 24vdc 48vdc 36vdc 75vdc under voltage lockout (uvlo) vin = 24v dc-dc on dc-dc off 8vdc 9vdc vin = 48v dc-dc on dc-dc off 16vdc 18vdc input filter pi - type input refected ripple (5) nominal vin and full load 30map-p input surge voltage vin = 24v, 100ms max. vin = 48v, 100ms max. 50vdc 100vdc start-up time power up remote on/off 30ms 30ms operating frequency range 360khz 400khz 440khz minimum load 0% optional output trim (6) 10.0% ripple and noise measured by 20mhz bandwidth with a 1f m/c x7r and 10f t/c with a 1f m/c x7r and 10f t/c single 3.3vout, 5vout 12vout, 15vout 75mvp-p 100mvp-p measured by 20mhz bandwidth with a 1f m/c x7r and 10f t/c for each output dual 100mvp-p remote on/off (6) positive logic dc-dc on dc-dc off open or 3 < vr < 15vdc short or 0 < vr < 1.2vdc negative logic dc-dc on dc-dc off short or 0 < vr < 1.2vdc open or 3 < vr < 15vdc input current of remote pin (ctrl) dc-dc off 2.5ma dc-dc on -0.5ma 1.0ma continued on next page specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted notes: note5: simulated source impedance of 12 h. 12h inductor in series with +vin. note6: the on/off control function can be positive or negative logic. the pin voltage is referenced to -vin pin. if no suffx is specifed, the control pin will be omitted. effciency vs. output current effciency vs. input voltage 9vin 24vin 36vin efficiency [%] output current [%] 10 60 55 50 45 40 65 70 75 80 90 95 20 40 60 80 100 30 50 70 90 85 efficiency [%] input voltage [vdc] 9 60 65 70 75 80 85 95 15 18 24 30 36 12 21 27 33 90 rp15-2405saw
dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted regulations parameter condition value output voltage accuracy full load and nominal vin 1% voltage adjustability single output 10% line voltage regulation single dual 0.2% 0.5% load voltage regulation 0% to 100% load single dual 0.2% 1.0% cross regulation asymmetrical 25%<>100% load 5% transient response recovery time 25% load step change 250 s typ. continued on next page rp15-aw series pd-3 rev.: 1/2016 www.recom-power.com effciency vs. output current effciency vs. input voltage 18vin 48vin 75vin efficiency [%] output current [%] 10 40 45 50 55 60 65 70 75 80 85 95 20 40 60 80 100 30 50 70 90 90 efficiency [%] input voltage [vdc] 18 65 70 75 80 85 95 30 36 48 60 75 24 42 54 66 90 rp15-4805saw trim up trim down r u 6 5 r d 4 5 external output trimming output voltage trimming single output powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim resistors. no general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing these trimming resistors. if voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resis tor required or use a variable resistor to set the output voltage. output can be externally trimmed by using the method shown below. trim up 1 2 3 4 5 6 7 8 9 10 % vout = 3.333 3.366 3.399 3.432 3.465 3.498 3.531 3.564 3.597 3.63 volts r u = 57.93 26.16 15.58 10.28 7.11 4.99 3.48 2.34 1.46 0.75 kohms trim down 1 2 3 4 5 6 7 8 9 10 % vout = 3.267 3.234 3.201 3.168 3.135 3.102 3.069 3.036 3.003 2.97 volts r d = 69.47 31.23 18.49 12.12 8.29 5.74 3.92 2.56 1.50 0.65 kohms rp15-xx3.3saw
pd-4 rev.: 1/2016 www.recom-power.com dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp15-aw series protections parameter condition value short circuit protection (scp) continuous, automatic recovery over voltage protection (ovp) zener diode clamp 3.3vout 5vout 12vout 15vout 3.7 - 5.4v 5.6 - 7.0v 13.5 - 19.6v 16.8-20.5v over load protection (olp) % of iout rated 150% typ. isolation voltage i/p to o/p i/p (o/p) to case 1.6kvdc/1 minute 1.0kvdc/1 minute isolation resistance 1g ? min. isolation capacitance 1000pf max. notes: note7: this power module is not internally fused. an input line fuse must always be used. trim up 1 2 3 4 5 6 7 8 9 10 % vout = 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.4 5.45 5.50 volts r u = 36.57 16.58 9.92 6.58 4.59 3.25 2.30 1.59 1.03 0.59 kohms trim down 1 2 3 4 5 6 7 8 9 10 % vout = 4.95 4.90 4.85 4.80 4.75 4.70 4.65 4.60 4.55 4.50 volts r d = 45.53 20.61 12.31 8.15 5.66 4.00 2.81 1.92 1.23 0.68 kohms rp15-xx05sa trim up 1 2 3 4 5 6 7 8 9 10 % vout = 12.12 12.24 12.36 12.48 12.60 12.72 12.84 12.96 13.08 13.20 volts r u = 367.91 165.95 98.64 64.98 44.78 31.32 21.70 14.49 8.88 4.39 kohms trim down 1 2 3 4 5 6 7 8 9 10 % vout = 11.88 11.76 11.64 11.52 11.40 11.28 11.16 11.04 10.92 10.8 volts r d = 460.99 207.95 123.60 81.42 56.12 39.25 27.20 18.16 11.13 5.51 kohms trim up 1 2 3 4 5 6 7 8 9 10 % vout = 15.15 15.3 15.45 15.60 15.75 15.90 16.05 16.20 16.35 16.50 volts r u = 404.18 180.59 106.06 68.80 46.44 31.53 20.88 12.90 6.69 1.72 kohms trim down 1 2 3 4 5 6 7 8 9 10 % vout = 14.85 14.70 14.55 14.40 14.25 14.10 13.95 13.80 13.65 13.50 volts r d = 499.82 223.41 131.27 85.20 57.56 39.14 25.97 16.10 8.42 2.282 kohms rp15-xx12sa rp15-xx15sa
dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp15-aw series pd-5 rev.: 1/2016 www.recom-power.com environmental parameter condition value operating temperature range without derating with derating -40c to +67c -40c to +105c maximum case temperature +105c temperature coeffcient 0.02%/c max. thermal impedance natural convection (20lfm) natural convection (20lfm) with heat sink 18.2c/watt 15.8c/watt operating humidity 5% - 95% rh thermal shock mil-std-810f vibration mil-std-810f mtbf mil-hdbk-217f bellcore tr-nwt-000332 (8) 1459 x 10 3 hours 1330 x 10 3 hours -40 60 67 80 105 100 120 40 20 0 -20 0 20 40 60 80 100 ambient temperature [c] output power [%] -40 60 73 80 100 120 105 40 20 0 -20 0 20 40 60 80 100 ambient temperature [c] output power [%] derating graph (9) notes: note8: bellcore tr-nwt-000332. case l: 50% stress, temperature at 40c. mil-hdbk 217f notice 2. ta = 25c, full load, (ground, benign, controlled environment). note9: derating graphs are valid only for the shown part numbers. if you need detailed derating-information about a part- number not shown here please contact our technical support service at techsupportat@recom-power.com. rp15-4805saw rp15-4805saw with heat-sink safety and certifications certifcate type (safety) report / file number standard ul general safety e196683 ul60950-1 1st ed.: 2003 c22.2 no. 60950 1st. ed.: 2003 emc compliance condition standard / criterion emi standard (10) with external flter en55022, class a, class b esd radiated immunity fast transient (11) surge (11) conducted immunity air 8kv and contact 6kv 10 v/m 2kv 1kv 3 vr.m.s en61000-4-2, criteria a en61000-4-3, criteria a en61000-4-4, criteria a en61000-4-5, criteria a en61000-4-6, criteria a continued on next page
pd-6 rev.: 1/2016 www.recom-power.com dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp15-aw series dimensions and physical characteristics parameter type value material case base potting nickel coated copper fr4 pcb epoxy (ul94-v0) package dimensions (lxwxh) without heat-sink with heat-sink 25.4 x 25.4 x 9.9mm 31.4 x 25.4 x 16.5mm package weight without heat-sink with heat-sink 15g 21.44g continued on next page input input dc dc fuse c3 c2 c1 +v in +v out -v out -v in load c4 c5 load load l1 dc dc fuse c3 c2 c1 +v in +v out -v out -v in c4 c5 l1 model c1 c2 c3 c4/c5 l1 rp15-24xxs_daw 6.8f/50v 1812 mlcc n/a 6.8f/50v 1812 mlcc 470pf/2kv 1808 mlcc cmc: 325 h ref: we 744290321 ref.: cmc-06 rp15-48xxs_daw 2.2f/100v 1812 mlcc 2.2f/100v 1812 mlcc 2.2f/100v 1812 mlcc 1000pf/2kv 1808 mlcc 325h ref: we 744290321 ref.: cmc-06 input input dc dc fuse c3 c2 c1 +v in +v out -v out -v in load c4 c5 load load l1 dc dc fuse c3 c2 c1 +v in +v out -v out -v in c4 c5 l1 emi filtering class b model c1 c2 c3/c4 rp15-24xxs_daw 6.8f/50v 1812 mlcc 6.8f/50v 1812 mlcc 470pf/2kv 1808 mlcc rp15-48xxs_daw 2.2f/100v 1812 mlcc 2.2f/100v 1812 mlcc 470pf/2kv 1808 mlcc input dc dc fuse c1 c2 +v in +v out -v out -v in load c4 c3 load load input dc dc fuse c1 c2 +v in +v out -v out -v in c4 c3 input dc dc fuse c1 c2 +v in +v out -v out -v in load c4 c3 load load input dc dc fuse c1 c2 +v in +v out -v out -v in c4 c3 emi filtering class a notes: note10: the standard modules meet emi class a or class b with external components, see flter suggestions below. note11: an external input flter capacitor is required if the module has to meet en61000-4-4, en61000-4-5. the flter capacitor recom suggests: nippon chemi-con ky series, 220 f/100v.
dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp15-aw series pd-7 rev.: 1/2016 www.recom-power.com dimension drawing (mm) dimension drawing (mm) with heat-sink 4 6 1 2 bottom view standard 4 6 1 2 bottom view ctrl version 5 3 25.4 5.60 9.90 20.32 25.4 ? 1.0 20.32 2.54 20.32 5.08 5.08 10.16 10.16 2.54 top view ?1.60 +0.15/-0 2.54 25.4 31.4 5.60 16.5 9.90 20.32 25.4 ? 1.0 2.54 24.20 24.20 top view heat-sink 5.85 pin connections pin # single single /p or /n dual dual /p or /n 1 +vin +vin +vin +vin 2 -vin -vin -vin -vin 3 no pin ctrl no pin ctrl 4 +vout +vout +vout +vout 5 no pin trim com com 6 -vout -vout -vout -vout case tolerance 0.5mm pin pitch tolerance 0.25mm xx.x 0.5mm xx.xx 0.25mm
pd-8 rev.: 1/2016 www.recom-power.com dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp15-aw series packaging information parameter type value packaging quantity without heat-sink with heat-sink tube tray 8pcs. 20pcs. storage temperature range -55c to +125c storage humidity 5% - 95% rh the product information and specifcations are subject to change without prior notice. recom products are not authorized for use in safety-critical applications (such as life support) without recoms explicit written consent. a safety-critical application is defned as an application where a failure of a recom product may reasonably be expected to endanger or cause loss of life, infict bodily harm or damage property. the buyer shall indemnify and hold harmless recom, its affliated companies and its representatives against any damage claims in connection with the unauthorized use of recom products in such safety-critical applications.
|
